NEET (Medical) · Physics

Mechanical Properties of Solids

30 practice questions with full step-by-step solutions, quick revision notes — free, no sign-up.

Reviewed by (19 years teaching)Written with AI helpReport a mistake

This chapter has

9
easy
15
medium
6
hard

Mechanical Properties of Solids — quick revision notes

This chapter covers how solids deform under load: stress, strain, Hooke's law, the stress–strain curve, and the three elastic moduli (Young's, bulk and shear), with applications to ropes, beams and mountains. NEET mostly asks ratio-type numericals on extension (ΔL = FL/AY), reading the stress–strain curve, and conceptual questions comparing moduli and materials.
  • Stress = F/A (N/m²); strain = ΔL/L, ΔV/V or θ (dimensionless). Hooke's law: stress ∝ strain up to the proportional limit.
  • Young's modulus Y = FL/(AΔL), so ΔL = FL/(πr²Y) and ΔL ∝ L/r² for the same material and load.
  • If a wire is stretched at constant volume, A ∝ 1/L, so ΔL ∝ L²: doubling the length gives 4 times the extension.
  • Bulk modulus B = −p/(ΔV/V); compressibility k = 1/B; B is largest for solids and smallest for gases. Liquids and gases have only a bulk modulus.
  • Shear modulus G = (F/A)/θ, where θ = Δx/L; for most solids G ≈ Y/3.
  • Stress–strain curve, in order: proportional limit, then yield point (elastic limit), then ultimate tensile strength, then fracture point. Ductile materials have a large gap between ultimate strength and fracture; in brittle materials the two are close. Elastomers (rubber, aorta) have no clear plastic region.
  • Beam sag δ = Wl³/(4bd³Y): a deeper beam stiffens it most (δ ∝ 1/d³), hence I-section beams. Maximum mountain height h = σ_elastic/(ρg), about 10 km.
  • Steel is more elastic than rubber (larger Y). A perfectly rigid body has infinite Y. Y depends on the material and temperature, not on the wire's dimensions.

Common mistakes to avoid

  • Using diameter in place of radius (or forgetting to square it) when finding the area in ΔL = FL/(AY).
  • Thinking rubber is more elastic than steel because it stretches more. Elasticity is measured by the modulus, and steel's is far larger.
  • Treating the elastic limit (yield point) and the proportional limit as the same point on the curve.
  • For a uniformly compressed sphere, writing Δr/r = ΔV/V. In fact Δr/r = (1/3)(ΔV/V).
Exam tip: Solve extension questions by ratios: write ΔL ∝ FL/r² (or ∝ L² at constant volume) and compare, rather than plugging in numbers. Learn the order and meaning of the points on the stress–strain curve; NEET often asks them as match-the-column.

Mechanical Properties of Solids — solved practice questions

8 NEET Physics questions with step-by-step solutions. Attempt each, then reveal the answer.

These worked examples are not in the timed test, so you can study them first.

  1. Q1easyReport

    A wire of cross-sectional area 2 mm² is pulled by a force of 100 N along its length. What is the tensile stress in the wire?

    • A5 × 108 N/m²
    • B2 × 107 N/m²
    • C5 × 105 N/m²
    • D5 × 107 N/m²
    Show answer & solution

    Correct answer: (D) 5 × 107 N/m²

    Stress = F/A = 100 / (2 × 10−6) = 5 × 107 N/m².
  2. Q2easyReport

    A wire 2 m long stretches by 1 mm when a load is hung from it. What is the longitudinal strain?

    • A0.5
    • B2 × 10−3
    • C5 × 10−3
    • D5 × 10−4
    Show answer & solution

    Correct answer: (D) 5 × 10−4

    Strain = ΔL/L = (1 × 10−3 m)/(2 m) = 5 × 10−4. Strain has no unit.
  3. Q3mediumReport

    A steel wire 2 m long with a cross-sectional area of 1 mm² carries a load of 20 N. Young's modulus of steel is 2 × 1011 N/m². What is the elongation of the wire?

    • A0.4 mm
    • B2 mm
    • C0.1 mm
    • D0.2 mm
    Show answer & solution

    Correct answer: (D) 0.2 mm

    ΔL = FL/(AY) = (20 × 2)/(10−6 × 2 × 1011) = 2 × 10−4 m = 0.2 mm. Check: stress = 2 × 107 Pa, so strain = 10−4, and ΔL = 10−4 × 2 m = 0.2 mm.
  4. Q4hardReport

    Two wires P and Q are made of the same material. Wire P has length L and diameter 2d. Wire Q has length 2L and diameter d. The same tensile force acts on both. What is the ratio of their extensions, ΔL_P : ΔL_Q?

    • A1 : 4
    • B1 : 2
    • C8 : 1
    • D1 : 8
    Show answer & solution

    Correct answer: (D) 1 : 8

    ΔL = FL/(AY), so ΔL ∝ L/d². For P: L/(4d²). For Q: 2L/d². Ratio = (1/4)/2 = 1/8.
  5. Q5easyReport

    Which of the following quantities is dimensionless?

    • AYoung's modulus
    • BLongitudinal strain
    • CStress
    • DBulk modulus
    Show answer & solution

    Correct answer: (B) Longitudinal strain

    Strain is the ratio of a change in length to the original length, so it has no unit or dimensions. Stress and all the moduli have units of N/m².
  6. Q6easyReport

    In the stress–strain curve of a metal wire, up to which point does Hooke's law (stress directly proportional to strain) hold?

    • AYield point
    • BProportional limit
    • CUltimate tensile strength
    • DFracture point
    Show answer & solution

    Correct answer: (B) Proportional limit

    The curve is a straight line, which is where Hooke's law holds, only up to the proportional limit. Between that point and the yield point the material is still elastic, but stress is no longer proportional to strain.
  7. Q7easyReport

    What is the Young's modulus of a perfectly rigid body?

    • AIt depends on the load applied
    • BZero
    • CInfinite
    • DUnity
    Show answer & solution

    Correct answer: (C) Infinite

    A perfectly rigid body shows no strain under any stress. Y = stress/strain, and the strain is zero, so Y is infinite.
  8. Q8mediumReport

    The bulk modulus of water is 2.2 × 109 N/m². By what percentage does a volume of water shrink when the pressure on it increases by 2.2 × 106 N/m²?

    • A0.01%
    • B0.1%
    • C1%
    • D10%
    Show answer & solution

    Correct answer: (B) 0.1%

    ΔV/V = Δp/B = (2.2 × 106)/(2.2 × 109) = 10−3, which is 0.1%.

Ready to test yourself? Take the 22-question Mechanical Properties of Solids test →