Higher Secondary 2027 (WBCHSE) · পদার্থবিদ্যা

Communication System (যোগাযোগ ব্যবস্থা) — Sem IV

20 practice questions with full step-by-step solutions, quick revision notes, 5 written questions with model answers — free, no sign-up.

Show first:

Reviewed by (19 years teaching)Written with AI helpReport a mistake

This chapter has

7
easy
10
medium
3
hard

Communication System (যোগাযোগ ব্যবস্থা) — Sem IV — quick revision notes

Communication System is a Semester IV chapter of WBCHSE Class 12 Physics. Semester IV is a written paper, so these MCQs are quick concept checks before you write full answers. The chapter covers the basic elements of a communication system (transmitter, channel, receiver), amplitude and frequency modulation, the bandwidths of common signals and transmission media, and how radio waves travel as sky waves and space waves. Learn the definitions and the short formulas for modulation index, AM bandwidth and line-of-sight range. Questions on these come up again and again.যোগাযোগ ব্যবস্থা WBCHSE দ্বাদশ শ্রেণির পদার্থবিদ্যার সেমেস্টার IV-এর অধ্যায়। সেমেস্টার IV লিখিত পরীক্ষা, তাই এই MCQ-গুলি পূর্ণ উত্তর লেখার আগে দ্রুত ধারণা যাচাইয়ের জন্য। এই অধ্যায়ে আছে যোগাযোগ ব্যবস্থার মৌলিক অংশ (প্রেরক, চ্যানেল, গ্রাহক), বিস্তার মডুলেশন ও কম্পাঙ্ক মডুলেশন, প্রচলিত সংকেত ও সঞ্চালন মাধ্যমের ব্যান্ডবিস্তার, এবং বেতার তরঙ্গ কীভাবে আকাশ তরঙ্গ ও ব্যোম (স্পেস) তরঙ্গ হিসেবে চলে। সংজ্ঞাগুলি এবং মডুলেশন সূচক, AM ব্যান্ডবিস্তার ও দৃষ্টিরেখা পাল্লার ছোট সূত্রগুলি শিখে রাখো। এগুলি থেকে বারবার প্রশ্ন আসে।
  • Every communication system has three basic elements: transmitter → channel → receiver. Noise is the unwanted signal added mainly in the channel. Attenuation is the loss of signal strength in the medium. A repeater is a receiver plus a transmitter.প্রতিটি যোগাযোগ ব্যবস্থার তিনটি মৌলিক অংশ: প্রেরক → চ্যানেল → গ্রাহক। নয়েজ হল অবাঞ্ছিত সংকেত, যা মূলত চ্যানেলে যুক্ত হয়। ক্ষীণন (অ্যাটেনুয়েশন) হল মাধ্যমে সংকেতের শক্তি হ্রাস। রিপিটার হল একটি গ্রাহক ও একটি প্রেরকের সমন্বয়।
  • Need for modulation: an antenna must be at least about λ/4 long. A 20 kHz signal has λ = 15 km, so it would need a 3.75 km antenna. Low-frequency signals are therefore carried on a high-frequency carrier.মডুলেশনের প্রয়োজনীয়তা: অ্যান্টেনার দৈর্ঘ্য অন্তত প্রায় λ/4 হতে হয়। 20 kHz সংকেতের λ = 15 km, তাই এর জন্য 3.75 km লম্বা অ্যান্টেনা লাগত। সেজন্য নিম্ন কম্পাঙ্কের সংকেতকে উচ্চ কম্পাঙ্কের বাহক তরঙ্গের সাহায্যে পাঠানো হয়।
  • Amplitude modulation (AM): the carrier's amplitude changes with the message. Modulation index μ = Am/Ac = (Amax − Amin)/(Amax + Amin). Keep μ ≤ 1 to avoid distortion.বিস্তার মডুলেশন (AM): বার্তা সংকেত অনুযায়ী বাহক তরঙ্গের বিস্তার বদলায়। মডুলেশন সূচক μ = Am/Ac = (Amax − Amin)/(Amax + Amin)। বিকৃতি এড়াতে μ ≤ 1 রাখতে হয়।
  • An AM wave contains three frequencies, fc, fc + fm and fc − fm (the sidebands), so AM bandwidth = 2fm.AM তরঙ্গে তিনটি কম্পাঙ্ক থাকে: fc, fc + fm এবং fc − fm (পার্শ্ব ব্যান্ড)। তাই AM ব্যান্ডবিস্তার = 2fm।
  • Frequency modulation (FM): the carrier's frequency changes with the message's amplitude while its amplitude stays constant. FM is less affected by noise and gives better quality, but needs a larger bandwidth than AM.কম্পাঙ্ক মডুলেশন (FM): বার্তা সংকেতের বিস্তার অনুযায়ী বাহকের কম্পাঙ্ক বদলায়, কিন্তু বাহকের বিস্তার স্থির থাকে। FM-এ নয়েজের প্রভাব কম ও গুণমান ভালো, তবে AM-এর চেয়ে বেশি ব্যান্ডবিস্তার লাগে।
  • Signal bandwidths: speech 2800 Hz (300–3100 Hz), music about 20 kHz, video 4.2 MHz, TV (picture + sound) about 6 MHz. Medium bandwidths: coaxial cable about 750 MHz, optical fibre above 100 GHz (the largest).সংকেতের ব্যান্ডবিস্তার: কথা 2800 Hz (300–3100 Hz), সংগীত প্রায় 20 kHz, ভিডিও 4.2 MHz, টিভি (ছবি + শব্দ) প্রায় 6 MHz। মাধ্যমের ব্যান্ডবিস্তার: কোঅ্যাক্সিয়াল কেবল প্রায় 750 MHz, অপটিক্যাল ফাইবার 100 GHz-এর বেশি (সর্বাধিক)।
  • Sky wave: the ionosphere bends (reflects) the wave back to Earth. This works from a few MHz up to about 30–40 MHz. Higher frequencies pass through the ionosphere and escape.আকাশ তরঙ্গ: আয়নমণ্ডল তরঙ্গকে বাঁকিয়ে (প্রতিফলিত করে) পৃথিবীতে ফেরত পাঠায়। এটি কয়েক MHz থেকে প্রায় 30–40 MHz পর্যন্ত কাজ করে। এর চেয়ে বেশি কম্পাঙ্কের তরঙ্গ আয়নমণ্ডল ভেদ করে বেরিয়ে যায়।
  • Space wave: line-of-sight travel, used above about 40 MHz (TV, microwave links, satellites). Range of a transmitting antenna is dT = √(2RhT). Maximum distance between two antennas is dM = √(2RhT) + √(2RhR).ব্যোম (স্পেস) তরঙ্গ: দৃষ্টিরেখা বরাবর চলে, প্রায় 40 MHz-এর বেশি কম্পাঙ্কে ব্যবহৃত হয় (টিভি, মাইক্রোওয়েভ লিঙ্ক, উপগ্রহ)। প্রেরক অ্যান্টেনার পাল্লা dT = √(2RhT)। দুটি অ্যান্টেনার মধ্যে সর্বাধিক দূরত্ব dM = √(2RhT) + √(2RhR)।

Common mistakes to avoid

  • Writing μ = Ac/Am instead of μ = Am/Ac. The modulation index of an undistorted AM wave can never be more than 1.
  • Taking AM bandwidth as fm or fc + fm. The correct bandwidth is 2fm, the gap between the upper and lower sidebands.
  • Thinking FM needs less bandwidth than AM. FM actually needs more bandwidth; its advantage is better noise immunity.
  • Using h in km with R in m in d = √(2Rh). Put both in metres, then convert the answer to km.
Exam tip: For any AM numerical, first write the sidebands fc ± fm and μ = Am/Ac. For range questions, convert everything to metres and use d = √(2Rh) with R = 6.4 × 106 m.পরীক্ষার টিপ: যেকোনো AM গাণিতিক প্রশ্নে আগে পার্শ্ব কম্পাঙ্ক fc ± fm এবং μ = Am/Ac লিখে নাও। পাল্লার প্রশ্নে সব রাশি মিটারে বদলে R = 6.4 × 10^6 m নিয়ে d = √(2Rh) ব্যবহার করো।

Communication System (যোগাযোগ ব্যবস্থা) — Sem IV — solved practice questions

12 WB HS Physics (পদার্থবিদ্যা) questions with step-by-step solutions. Attempt each, then reveal the answer.

Take the timed test first

These questions are in the test, so try it before you read the answers below.

Start · 20 questions
  1. Q1easyReport

    The three basic units of any communication system are:

    যেকোনো যোগাযোগ ব্যবস্থার তিনটি মৌলিক অংশ হল:
    • AMicrophone, speaker and repeaterমাইক্রোফোন, স্পিকার ও রিপিটার
    • BTransmitter, channel and receiverপ্রেরক (ট্রান্সমিটার), চ্যানেল ও গ্রাহক (রিসিভার)
    • CTransducer, filter and detectorট্রান্সডিউসার, ফিল্টার ও ডিটেক্টর
    • DModulator, amplifier and antennaমডুলেটর, বিবর্ধক ও অ্যান্টেনা
    Show answer & solution

    Correct answer: (B) Transmitter, channel and receiver

    Every communication system has a transmitter that sends the signal, a channel that carries it, and a receiver that picks it up.প্রতিটি যোগাযোগ ব্যবস্থায় থাকে প্রেরক, যা সংকেত পাঠায়; চ্যানেল, যা সংকেত বহন করে; এবং গ্রাহক, যা সংকেত গ্রহণ করে।
  2. Q2easyReport

    The unwanted signal that disturbs the transmission and processing of message signals in a communication system is called

    যোগাযোগ ব্যবস্থায় বার্তা সংকেতের প্রেরণ ও প্রক্রিয়াকরণে বিঘ্ন ঘটায় এমন অবাঞ্ছিত সংকেতকে বলে
    • Aattenuationক্ষীণন (অ্যাটেনুয়েশন)
    • Bmodulationমডুলেশন
    • Cnoiseনয়েজ
    • Damplificationবিবর্ধন
    Show answer & solution

    Correct answer: (C) noise

    Noise is an unwanted signal that gets added to the message, mostly in the channel, and disturbs it.নয়েজ হল অবাঞ্ছিত সংকেত, যা মূলত চ্যানেলে বার্তার সঙ্গে যুক্ত হয়ে বিঘ্ন ঘটায়।
  3. Q3mediumReport

    The loss of strength of a signal while it propagates through a medium is known as

    কোনো মাধ্যমের মধ্য দিয়ে যাওয়ার সময় সংকেতের শক্তি হ্রাস পাওয়াকে বলে
    • Aattenuationক্ষীণন (অ্যাটেনুয়েশন)
    • Bmodulationমডুলেশন
    • Cdemodulationডিমডুলেশন
    • Dnoiseনয়েজ
    Show answer & solution

    Correct answer: (A) attenuation

    Attenuation is the weakening (loss of strength) of a signal as it travels through the medium.মাধ্যমের মধ্য দিয়ে চলার সময় সংকেত দুর্বল হয়ে যাওয়া বা শক্তি হারানোকে ক্ষীণন বলে।
  4. Q4mediumReport

    A repeater used in a communication system is a combination of

    যোগাযোগ ব্যবস্থায় ব্যবহৃত রিপিটার হল কোনগুলির সমন্বয়?
    • Aa modulator and a demodulatorএকটি মডুলেটর ও একটি ডিমডুলেটর
    • Ba detector and a filterএকটি ডিটেক্টর ও একটি ফিল্টার
    • Ca transmitter and an antenna onlyশুধু একটি প্রেরক ও একটি অ্যান্টেনা
    • Da receiver and a transmitterএকটি গ্রাহক ও একটি প্রেরক
    Show answer & solution

    Correct answer: (D) a receiver and a transmitter

    A repeater picks up the signal (receiver), amplifies it, and sends it out again (transmitter). This extends the range of communication.রিপিটার সংকেত গ্রহণ করে (গ্রাহক), বিবর্ধিত করে আবার পাঠিয়ে দেয় (প্রেরক)। এতে যোগাযোগের পাল্লা বাড়ে।
  5. Q5easyReport

    A device that converts one form of energy into another, such as a microphone converting sound into an electrical signal, is called

    যে যন্ত্র শক্তির এক রূপকে অন্য রূপে বদলায়, যেমন মাইক্রোফোন শব্দকে বৈদ্যুতিক সংকেতে বদলায়, তাকে বলে
    • Aa transducerট্রান্সডিউসার
    • Ban amplifierবিবর্ধক
    • Ca demodulatorডিমডুলেটর
    • Da repeaterরিপিটার
    Show answer & solution

    Correct answer: (A) a transducer

    A transducer converts energy from one form to another. A microphone converts sound energy into an electrical signal.ট্রান্সডিউসার শক্তির এক রূপকে অন্য রূপে বদলায়। মাইক্রোফোন শব্দশক্তিকে বৈদ্যুতিক সংকেতে রূপান্তরিত করে।
  6. Q6easyReport

    In frequency modulation (FM), which characteristic of the carrier wave varies according to the instantaneous amplitude of the message signal?

    কম্পাঙ্ক মডুলেশনে (FM) বার্তা সংকেতের তাৎক্ষণিক বিস্তার অনুযায়ী বাহক তরঙ্গের কোন বৈশিষ্ট্যটি পরিবর্তিত হয়?
    • AFrequencyকম্পাঙ্ক
    • BAmplitudeবিস্তার
    • CPolarisationসমবর্তন
    • DVelocityবেগ
    Show answer & solution

    Correct answer: (A) Frequency

    In FM the carrier's frequency changes according to the message signal's amplitude, while the carrier's amplitude stays constant.FM-এ বার্তা সংকেতের বিস্তার অনুযায়ী বাহকের কম্পাঙ্ক বদলায়, কিন্তু বাহকের বিস্তার স্থির থাকে।
  7. Q7mediumReport

    A carrier wave of peak amplitude 10 V is amplitude modulated by a message signal of peak amplitude 5 V. The modulation index is

    10 V শীর্ষ বিস্তারের একটি বাহক তরঙ্গকে 5 V শীর্ষ বিস্তারের একটি বার্তা সংকেত দ্বারা বিস্তার মডুলেশন করা হল। মডুলেশন সূচক হবে
    • A1.51.5
    • B0.20.2
    • C0.50.5
    • D22
    Show answer & solution

    Correct answer: (C) 0.5

    μ = Am/Ac = 5/10 = 0.5.μ = Am/Ac = 5/10 = 0.5।
  8. Q8mediumReport

    A 1 MHz carrier wave is amplitude modulated by a 5 kHz audio signal. The side band frequencies are

    একটি 1 MHz বাহক তরঙ্গকে 5 kHz শ্রাব্য সংকেত দ্বারা বিস্তার মডুলেশন করা হল। পার্শ্ব ব্যান্ড কম্পাঙ্কগুলি হবে
    • A1005 kHz and 1000 kHz1005 kHz ও 1000 kHz
    • B1005 kHz and 995 kHz1005 kHz ও 995 kHz
    • C1 MHz and 5 kHz1 MHz ও 5 kHz
    • D1010 kHz and 990 kHz1010 kHz ও 990 kHz
    Show answer & solution

    Correct answer: (B) 1005 kHz and 995 kHz

    The sidebands are at fc ± fm = 1000 kHz ± 5 kHz, which gives 1005 kHz and 995 kHz.পার্শ্ব ব্যান্ড থাকে fc ± fm = 1000 kHz ± 5 kHz কম্পাঙ্কে, অর্থাৎ 1005 kHz ও 995 kHz।
  9. Q9hardReport

    An amplitude modulated wave has a maximum amplitude of 15 V and a minimum amplitude of 5 V. Its modulation index is

    একটি বিস্তার মডুলেটেড তরঙ্গের সর্বাধিক বিস্তার 15 V এবং সর্বনিম্ন বিস্তার 5 V। এর মডুলেশন সূচক হল
    • A0.50.5
    • B33
    • C0.330.33
    • D22
    Show answer & solution

    Correct answer: (A) 0.5

    μ = (Amax − Amin)/(Amax + Amin) = (15 − 5)/(15 + 5) = 0.5. Check: Ac = (15 + 5)/2 = 10 V and Am = (15 − 5)/2 = 5 V, so Am/Ac = 0.5.μ = (Amax − Amin)/(Amax + Amin) = (15 − 5)/(15 + 5) = 0.5। যাচাই: Ac = (15 + 5)/2 = 10 V এবং Am = (15 − 5)/2 = 5 V, তাই Am/Ac = 0.5।
  10. Q10mediumReport

    The main advantage of frequency modulation (FM) over amplitude modulation (AM) is that FM

    বিস্তার মডুলেশনের (AM) তুলনায় কম্পাঙ্ক মডুলেশনের (FM) প্রধান সুবিধা হল, FM
    • Aneeds much simpler circuitsঅনেক সরল বর্তনী লাগে
    • Brequires a smaller bandwidthকম ব্যান্ডবিস্তার নেয়
    • Cis much less affected by noiseনয়েজ দ্বারা অনেক কম প্রভাবিত হয়
    • Dtravels farther as a ground waveভূমি তরঙ্গ হিসেবে বেশি দূর যায়
    Show answer & solution

    Correct answer: (C) is much less affected by noise

    Noise mostly changes a signal's amplitude. FM carries the message in frequency changes, so it is much less affected by noise. FM actually needs a larger bandwidth than AM.নয়েজ মূলত সংকেতের বিস্তার বদলায়। FM বার্তা বহন করে কম্পাঙ্কের পরিবর্তনের মাধ্যমে, তাই নয়েজের প্রভাব অনেক কম। বাস্তবে AM-এর চেয়ে FM-এর বেশি ব্যান্ডবিস্তার লাগে।
  11. Q11easyReport

    The frequency range considered adequate for telephonic speech communication corresponds to a bandwidth of about

    টেলিফোনে কথা বলার জন্য পর্যাপ্ত কম্পাঙ্ক পাল্লার ব্যান্ডবিস্তার প্রায়
    • A200 kHz200 kHz
    • B4.2 MHz4.2 MHz
    • C20 kHz20 kHz
    • D2800 Hz2800 Hz
    Show answer & solution

    Correct answer: (D) 2800 Hz

    Speech needs the range 300 Hz to 3100 Hz, which is a bandwidth of 2800 Hz.কথার জন্য 300 Hz থেকে 3100 Hz পাল্লা লাগে, অর্থাৎ ব্যান্ডবিস্তার 2800 Hz।
  12. Q12easyReport

    The bandwidth required for transmitting video (picture) signals is about

    ভিডিও (ছবি) সংকেত প্রেরণের জন্য প্রয়োজনীয় ব্যান্ডবিস্তার প্রায়
    • A2800 Hz2800 Hz
    • B4.2 MHz4.2 MHz
    • C20 kHz20 kHz
    • D200 kHz200 kHz
    Show answer & solution

    Correct answer: (B) 4.2 MHz

    Video signals need a bandwidth of about 4.2 MHz. A TV signal carries both picture and sound, so it is usually given about 6 MHz.ভিডিও সংকেতের জন্য প্রায় 4.2 MHz ব্যান্ডবিস্তার লাগে। টিভি সংকেতে ছবি ও শব্দ দুটোই থাকে, তাই সাধারণত প্রায় 6 MHz বরাদ্দ করা হয়।

Want the full set? Practise all 20 Communication System (যোগাযোগ ব্যবস্থা) — Sem IV questions →

Communication System (যোগাযোগ ব্যবস্থা) — Sem IV — written answers with model answers

Most WB HS marks come from written answers. Write yours the way you would in the exam, then compare it with the model answer and tick the marking points you covered.

Short answers (3 marks)

  1. Q1 · Short3 marks
    (a) Why is modulation needed to transmit a low-frequency audio signal? (1) (b) Find the minimum length of antenna (λ/4) needed to transmit a 20 kHz signal directly, and comment on your result. (2)(a) নিম্ন কম্পাঙ্কের শব্দ সংকেত প্রেরণের জন্য মডুলেশন (modulation) প্রয়োজন কেন? (1) (b) 20 kHz সংকেত সরাসরি প্রেরণের জন্য প্রয়োজনীয় অ্যান্টেনার ন্যূনতম দৈর্ঘ্য (λ/4) নির্ণয় করো এবং ফলাফল সম্পর্কে মন্তব্য করো। (2)
    Model answer & marking points(a) An antenna must be at least about λ/4 long to radiate a signal well. Low-frequency signals have very long wavelengths, so the antenna would be impossibly long; also the power radiated at low frequency is very small and signals from different stations would mix. So the signal is carried on a high-frequency carrier. (b) λ = c/f = (3 × 10⁸)/(20 × 10³) = 1.5 × 10⁴ m = 15 km. Antenna length = λ/4 = 15/4 = 3.75 km. Such an antenna is not practical, which shows why modulation is needed.(a) ভালোভাবে সংকেত বিকিরণের জন্য অ্যান্টেনার দৈর্ঘ্য অন্তত প্রায় λ/4 হতে হয়। নিম্ন কম্পাঙ্কের সংকেতের তরঙ্গদৈর্ঘ্য অনেক বড়ো, তাই অ্যান্টেনা অসম্ভব রকম লম্বা হবে; তাছাড়া নিম্ন কম্পাঙ্কে বিকিরিত ক্ষমতা খুব কম এবং বিভিন্ন কেন্দ্রের সংকেত মিশে যাবে। তাই সংকেতকে উচ্চ কম্পাঙ্কের বাহক তরঙ্গের (carrier) সাহায্যে পাঠানো হয়। (b) λ = c/f = (3 × 10⁸)/(20 × 10³) = 1.5 × 10⁴ m = 15 km। অ্যান্টেনার দৈর্ঘ্য = λ/4 = 15/4 = 3.75 km। এমন অ্যান্টেনা বাস্তবে সম্ভব নয়, যা মডুলেশনের প্রয়োজনীয়তা দেখায়।

    Tick what your answer has:

  2. Q2 · Short3 marks
    In an amplitude modulated wave, the maximum amplitude is 10 V and the minimum amplitude is 2 V. Find the modulation index, and the amplitudes of the carrier wave and the message signal. Why should the modulation index not exceed 1?একটি বিস্তার মডুলেটেড (amplitude modulated) তরঙ্গের সর্বোচ্চ বিস্তার 10 V এবং সর্বনিম্ন বিস্তার 2 V। মডুলেশন সূচক (modulation index), বাহক তরঙ্গ ও বার্তা সংকেতের বিস্তার নির্ণয় করো। মডুলেশন সূচক 1-এর বেশি হওয়া উচিত নয় কেন?
    Model answer & marking pointsA_max = A_c + A_m = 10 V and A_min = A_c - A_m = 2 V, so A_c = 6 V and A_m = 4 V. μ = (A_max - A_min)/(A_max + A_min) = (10 - 2)/(10 + 2) = 8/12 ≈ 0.67 (also A_m/A_c = 4/6). If μ > 1 (over-modulation), the envelope no longer follows the message; the wave is distorted and the message cannot be recovered correctly.A_max = A_c + A_m = 10 V এবং A_min = A_c - A_m = 2 V, অতএব A_c = 6 V এবং A_m = 4 V। μ = (A_max - A_min)/(A_max + A_min) = (10 - 2)/(10 + 2) = 8/12 ≈ 0.67 (একইভাবে A_m/A_c = 4/6)। μ > 1 হলে (অতি-মডুলেশন) আবরণী (envelope) আর বার্তাকে অনুসরণ করে না; তরঙ্গ বিকৃত হয় এবং বার্তা সঠিকভাবে পুনরুদ্ধার করা যায় না।

    Tick what your answer has:

  3. Q3 · Short3 marks
    A carrier wave of frequency 1 MHz is amplitude modulated by a message signal of frequency 5 kHz. Find the frequencies present in the modulated wave and the bandwidth required. Which of these are called sidebands?1 MHz কম্পাঙ্কের একটি বাহক তরঙ্গকে 5 kHz কম্পাঙ্কের একটি বার্তা সংকেত দ্বারা বিস্তার মডুলেট করা হল। মডুলেটেড তরঙ্গে উপস্থিত কম্পাঙ্কগুলি এবং প্রয়োজনীয় ব্যান্ডপ্রস্থ (bandwidth) নির্ণয় করো। এগুলির মধ্যে কোনগুলিকে পার্শ্বব্যান্ড (sideband) বলে?
    Model answer & marking pointsf_c = 1 MHz = 1000 kHz, f_m = 5 kHz. Frequencies present: f_c = 1000 kHz, f_c + f_m = 1005 kHz and f_c - f_m = 995 kHz. Bandwidth = (f_c + f_m) - (f_c - f_m) = 2f_m = 10 kHz. 1005 kHz is the upper sideband and 995 kHz the lower sideband.f_c = 1 MHz = 1000 kHz, f_m = 5 kHz। উপস্থিত কম্পাঙ্ক: f_c = 1000 kHz, f_c + f_m = 1005 kHz এবং f_c - f_m = 995 kHz। ব্যান্ডপ্রস্থ = (f_c + f_m) - (f_c - f_m) = 2f_m = 10 kHz। 1005 kHz ঊর্ধ্ব পার্শ্বব্যান্ড এবং 995 kHz নিম্ন পার্শ্বব্যান্ড।

    Tick what your answer has:

  4. Q4 · Short3 marks
    Distinguish between amplitude modulation and frequency modulation (three points).বিস্তার মডুলেশন (AM) ও কম্পাঙ্ক মডুলেশনের (FM) মধ্যে তিনটি পার্থক্য লেখো।
    Model answer & marking points1. In AM the amplitude of the carrier changes according to the message signal while its frequency stays constant; in FM the frequency of the carrier changes according to the amplitude of the message while its amplitude stays constant. 2. AM is more affected by noise (noise mainly changes amplitude); FM is much less affected by noise and gives better sound quality. 3. AM needs a smaller bandwidth (2f_m); FM needs a much larger bandwidth.1. AM-এ বার্তা সংকেত অনুযায়ী বাহকের বিস্তার পরিবর্তিত হয়, কম্পাঙ্ক স্থির থাকে; FM-এ বার্তার বিস্তার অনুযায়ী বাহকের কম্পাঙ্ক পরিবর্তিত হয়, বিস্তার স্থির থাকে। 2. AM নয়েজ দ্বারা বেশি প্রভাবিত হয় (নয়েজ প্রধানত বিস্তার বদলায়); FM নয়েজ দ্বারা অনেক কম প্রভাবিত হয় এবং শব্দের গুণমান ভালো হয়। 3. AM-এ কম ব্যান্ডপ্রস্থ (2f_m) লাগে; FM-এ অনেক বেশি ব্যান্ডপ্রস্থ লাগে।

    Tick what your answer has:

  5. Q5 · Short3 marks
    A TV transmitting antenna is 80 m tall and a receiving antenna is 20 m tall. Find the range of the transmitting antenna and the maximum line-of-sight distance between the two antennas. Why are TV signals sent by space waves and not by sky waves? (Radius of the earth = 6.4 × 10⁶ m)একটি টিভি প্রেরক অ্যান্টেনার উচ্চতা 80 m এবং একটি গ্রাহক অ্যান্টেনার উচ্চতা 20 m। প্রেরক অ্যান্টেনার পাল্লা এবং দুটি অ্যান্টেনার মধ্যে সর্বোচ্চ দৃষ্টিরেখা দূরত্ব (line-of-sight distance) নির্ণয় করো। টিভি সংকেত আকাশ তরঙ্গে (sky wave) না পাঠিয়ে মহাশূন্য তরঙ্গে (space wave) পাঠানো হয় কেন? (পৃথিবীর ব্যাসার্ধ = 6.4 × 10⁶ m)
    Model answer & marking pointsd_T = √(2Rh_T) = √(2 × 6.4 × 10⁶ × 80) = √(1.024 × 10⁹) = 3.2 × 10⁴ m = 32 km. d_R = √(2Rh_R) = √(2 × 6.4 × 10⁶ × 20) = √(2.56 × 10⁸) = 1.6 × 10⁴ m = 16 km. d_M = d_T + d_R = 32 + 16 = 48 km. TV signals have frequencies above about 40 MHz (tens to hundreds of MHz). At such high frequencies the ionosphere does not bend the waves back; they pass through and escape, so sky-wave propagation is not possible and line-of-sight space waves are used.d_T = √(2Rh_T) = √(2 × 6.4 × 10⁶ × 80) = √(1.024 × 10⁹) = 3.2 × 10⁴ m = 32 km। d_R = √(2Rh_R) = √(2 × 6.4 × 10⁶ × 20) = √(2.56 × 10⁸) = 1.6 × 10⁴ m = 16 km। d_M = d_T + d_R = 32 + 16 = 48 km। টিভি সংকেতের কম্পাঙ্ক প্রায় 40 MHz-এর বেশি (দশ থেকে শত MHz)। এত উচ্চ কম্পাঙ্কে আয়নমণ্ডল তরঙ্গকে ফিরিয়ে দেয় না; তরঙ্গ তা ভেদ করে বেরিয়ে যায়, তাই আকাশ তরঙ্গে প্রেরণ সম্ভব নয় এবং দৃষ্টিরেখা বরাবর মহাশূন্য তরঙ্গ ব্যবহার করা হয়।

    Tick what your answer has:

Ready for a full paper? HS 2027 Semester IV model papers with answers → · The most-marked questions: important questions → · Plan your weeks: Semester IV study plan →