Class 10 (ICSE) · Chemistry
Electrolysis and Metallurgy
20 practice questions with full step-by-step solutions, quick revision notes — free, no sign-up.
Reviewed by Kaustav Basak (19 years teaching)Written with AI helpReport a mistake
This chapter has
Electrolysis and Metallurgy — quick revision notes
- Strong electrolytes (NaCl, KOH, dilute H2SO4) are almost fully ionised. Weak electrolytes (acetic acid, NH4OH, carbonic acid) are partly ionised, so they contain both ions and molecules.
- Oxidation is the loss of electrons and happens at the anode. Reduction is the gain of electrons and happens at the cathode.
- Selective discharge: the lower a cation is in the activity series (K, Na, Ca, Mg, Al, Zn, Fe, Pb, H, Cu, Ag), the more easily it is discharged. So Cu2+ is discharged before H+, and H+ before Na+.
- Molten PbBr2: grey lead forms at the cathode (Pb2+ + 2e- -> Pb) and reddish-brown bromine vapour at the anode (2Br- -> Br2 + 2e-). Acidified water with Pt electrodes gives H2 and O2 in the ratio 2:1 by volume.
- Aqueous CuSO4 with Pt electrodes: Cu is deposited, O2 is given off, the blue colour fades and the solution turns acidic. With Cu electrodes, the anode dissolves and the colour stays the same.
- Electroplating: the article is the cathode and a block of the plating metal is the anode. Nickel sulphate is the electrolyte for nickel and sodium argentocyanide for silver. Electrorefining of copper uses an impure Cu anode, a pure Cu cathode and acidified CuSO4; Ag and Au collect as anode mud.
- Ores: haematite Fe2O3, magnetite Fe3O4, bauxite Al2O3.2H2O, cryolite Na3AlF6, zinc blende ZnS, calamine ZnCO3. Sulphide ores are concentrated by froth flotation.
- Roasting is heating in excess air, mainly for sulphide ores. Calcination is heating in little or no air, mainly for carbonate and hydrated ores. CuO, PbO, ZnO and Fe2O3 can be reduced by C, CO or H2. Na, K, Ca, Mg and Al need electrolytic reduction.
- Hall-Heroult: alumina is dissolved in molten cryolite with fluorspar. Cryolite lowers the fusion temperature and improves conductivity, and fluorspar increases fluidity. Al forms at the carbon-lined cathode. The graphite anodes burn away as the O2 released there forms CO2. Alloys: brass (Cu, Zn), bronze (Cu, Sn, Zn), duralumin (Al, Cu, Mg, Mn), magnalium (Al, Mg), stainless steel (Fe, Cr, Ni, C), solder (Pb, Sn).
Common mistakes to avoid
- Calling Cu -> Cu2+ + 2e- a reduction. Losing electrons is oxidation, and it always happens at the anode.
- Thinking the CuSO4 solution loses its colour whatever the electrodes. It fades only with inert (Pt or graphite) electrodes, not with copper electrodes.
- Mixing up roasting and calcination, or counting calcination as a way of concentrating ore. Calcination is a heat treatment done after concentration.
- Swapping brass (Cu + Zn) and bronze (Cu + Sn), or thinking duralumin and magnalium contain iron.
Electrolysis and Metallurgy — solved practice questions
5 ICSE 10 Chemistry questions with step-by-step solutions. Attempt each, then reveal the answer.
These worked examples are not in the timed test, so you can study them first.
- Q1easyReport
Which of the following is a weak electrolyte?
- AAcetic acid solution
- BPotassium hydroxide solution
- CSodium chloride solution
- DDilute sulphuric acid
Show answer & solution
Correct answer: (A) Acetic acid solution
Acetic acid ionises only partly in water, so it gives few ions and conducts poorly. That makes it a weak electrolyte. NaCl, dilute H2SO4 and KOH are almost completely ionised, so they are strong electrolytes. - Q2easyReport
Which of the following contains both ions and molecules?
- AMolten lead bromide
- BCarbon tetrachloride
- CGlucose solution
- DAmmonium hydroxide solution
Show answer & solution
Correct answer: (D) Ammonium hydroxide solution
Ammonium hydroxide is a weak electrolyte. It ionises only partly, so its solution contains NH4+ and OH- ions as well as un-ionised molecules. Carbon tetrachloride and glucose solution contain only molecules, and molten lead bromide contains only ions. - Q3easyReport
During the electrolysis of molten lead bromide, which reaction takes place at the cathode?
- ABr2 + 2e- -> 2Br-
- B2Br- -> Br2 + 2e-
- CPb -> Pb2+ + 2e-
- DPb2+ + 2e- -> Pb
Show answer & solution
Correct answer: (D) Pb2+ + 2e- -> Pb
Cations move to the cathode and gain electrons there. Pb2+ ions take 2 electrons each and are deposited as grey lead metal. Bromide ions lose electrons at the anode, giving off reddish-brown bromine vapour. - Q4easyReport
Solid lead bromide does not conduct electricity, but molten lead bromide does. Why?
- AIn the solid the ions are held in fixed positions in the crystal lattice, and melting sets them free to move
- BSolid lead bromide is made up only of molecules
- CMelting produces free electrons in lead bromide
- DHeating converts lead bromide into metallic lead
Show answer & solution
Correct answer: (A) In the solid the ions are held in fixed positions in the crystal lattice, and melting sets them free to move
Lead bromide is an ionic compound. In the solid, strong electrostatic forces hold the Pb2+ and Br- ions in a rigid lattice, so they cannot move. When the solid melts, the ions become mobile and can carry current to the electrodes. - Q5mediumReport
When aqueous copper sulphate is electrolysed with copper electrodes, the anode reaction is Cu -> Cu2+ + 2e-. In this reaction, the copper atom is:
- Aoxidised, because it loses electrons
- Breduced, because it loses electrons
- Coxidised, because it gains electrons
- Dreduced, because it gains electrons
Show answer & solution
Correct answer: (A) oxidised, because it loses electrons
In electronic terms, oxidation is the loss of electrons. Each copper atom gives up 2 electrons and becomes a Cu2+ ion, so copper is oxidised. Oxidation always takes place at the anode.
Ready to test yourself? Take the 15-question Electrolysis and Metallurgy test →